Team Chevelle banner
Cancel
Create thread New Garage Forums

grill removing.

Jump to Latest
Status
Not open for further replies.
1 - 20 of 27 Posts
#2 ·
What you need to do to do it right is to remove the headlamp buckets.

To do that you need to remove the headlamps and their chrom trim rings. After that it should be easy. However I do not know if factory were phillips head or torx head screws. If they are torx and you don't have any a small enough hex key will work but go slow.

------------------
Francis Taracido Gold# 201
sniper0666@aol.com
History shows again and again how nature points out the folly of man.
Oh No! You Know She's Got To Go!
Go Go Quadzilla! <oo=+=oo>
 
Save
Like Like
#4 ·
sawzall
 
Save
Like Like
#6 ·
just messin with you Chaos......no need to cut that pretty car up
Image


Hey when are you going to post some pictures of that car?
 
Save
Like Like
#8 ·
Okay the Sawzall is a tool made by Makita. It is a reciprocating saw that claims to saw all hence the name.

------------------
Francis Taracido Gold# 201
sniper0666@aol.com
History shows again and again how nature points out the folly of man.
Oh No! You Know She's Got To Go!
Go Go Quadzilla! <oo=+=oo>
 
Save
Like Like
#10 ·
put up a link to some pics, and I'll promise not to use my "Milwakee" sawzall on this 72 grill I'm not using
Image
 
Save
Like Like
#12 ·
Will that be Visa or Mastercard?
**hint...hint**

[This message has been edited by Big Block Dave (edited 05-17-2001).]
 
Save
Like Like
#15 ·
Chaos.. Did you get any pictures of your smokey burnout?

------------------
You can sleep in your car,but you cant drive your house.
Tony. H . 406 powered , Mohave Gold , 72'Malibu
 
#16 ·
I was rather unsure about the torx thing but I found a lot of Torx used on my 70 holding the front end on, grill & buckets

------------------
Francis Taracido Gold# 201
sniper0666@aol.com
History shows again and again how nature points out the folly of man.
Oh No! You Know She's Got To Go!
Go Go Quadzilla! <oo=+=oo>
 
Save
Like Like
#17 ·
No Torx in 71-72. Quad, you must have a "molested" font end. Who knows, it may have went back to the dealer for something and they "updated" them.
 
Save
Like Like
Discussion starter · #18 ·
Sent the picture to Beldarr...
Hope that it will be up soon.

I also sent him a picture of my original dash.. 4 spoke wheel and a 200 odometer. (only less than 900 were made)

Its a rough picture.. but you can see that the 120 digit is in the middle of the scale.. and not at the end like your scales.

It was design to show KPH.. but it can be adjusted to show MPH..

I wonder how much that dash will sell for
Image

Its an original GM 1972 Malibu dash..
But it has that rare 200 on the odometer.
 
#19 ·
<BLOCKQUOTE>quote:</font><HR>Originally posted by Quadzilla:
Okay the Sawzall is a tool made by Makita. It is a reciprocating saw that claims to saw all hence the name.
<HR></BLOCKQUOTE>

Most all of mine were made by Millwalkee, except for one, It's a Porter Cable




------------------
Dean Call
Team Gold member #3
A.C.E.S. # 00235
Mid America Chevelle Club #001
chevelles.net
My 69

ACES/Midwest Chevelle Regionals

Never lend your car to anyone to whom you have given birth.
 
#20 ·
Ditto Dean..my favorite tool, especially for cutting the roofs off of 4 doors!
Image


------------------
Dave (NY)
70 chevelle ss396 conv
66 chevelle ss396 hdp/conv
72 chevelle
TC member #493
Never forget Earnhardt!
 
Save
Like Like
1 - 20 of 27 Posts
Status
Not open for further replies.
You have insufficient privileges to reply here.
About this Discussion
26 Replies
11 Participants
Last post:
BAD415
Team Chevelle
posts
5.3M
members
131K
Since
1998
A forum community dedicated to Chevrolet Chevelle owners and enthusiasts. Come join the discussion about restorations, builds, performance, modifications, classifieds, troubleshooting, maintenance, and more!
Full Forum Listing
Explore Our Forums
Bench Racing Performance Engine Chevelle Tech Body Shop