engineguy engineguy is offline
Senior Tech Team
- About engineguy
- Gold Canyon, AZ
- NHRA Drag Racing - Super Stock Modified
- Sales Mgr., Engine Parts Manufacturer
- Piston Factor
- Currently own:
- 2005 Chev. C3500
2005 Chev. Impala
2001 Chev. Camaro
1974 Chev. C20
1964 Chev. Chevelle
1966 Hough Loader
1952 Ford F-6
1998 John Deere 345
- Photo Link
- First Name
- Bill R
64 Chevelle Malibu Sport Coupe (original owner) car now has 427" BB, Jerico 5-spd. trans., Dana 60 rear end.
SAE Member (25+ years)
ASE Master Certified Engine Machinist
AERA Certified Professional Engine Machinist
|Dec 3rd, 19|
|10:57 AM - Qwiktripz1320 quoted engineguy in post Re: In need of an oil pump shaft
If anyone has an old Hoof Prod...
|Nov 27th, 19|
|10:36 PM - engineguy quoted mrpaticular in post Re: Fuel Lines
1/2 is good. You also need filte...
|Mar 25th, 19|
|12:33 AM - DZAUTO quoted engineguy in post Re: Recommended ring gap for Speed Pro hypereutectic pistons
Like BillK stated in an earlie...
|Mar 23rd, 19|
|6:05 PM - engineguy quoted sleeper in post Re: Interesting valve failure
...ts in the heads. Sleeper, I don't think this...
|9:35 AM - CNC BLOCKS N/E quoted engineguy in post Re: Beginner question...main journal measurements
Sunnen brand is the very best ...
|Jan 17th, 19|
|8:25 PM - novass quoted engineguy in post Re: Fenderwell headers anyone?
Mike, Nice job with the carbo...
|Dec 17th, 18|
|6:23 PM - bjl95mustang quoted engineguy in post Re: Questions on my new car
The oil pan issue is very impo...
|Dec 10th, 18|
|11:20 PM - ZZ69chevelle quoted engineguy in post Re: Questions on 2.5" vs 3" Exhaust
When the air fuel mixture is i...
|10:02 PM - engineguy quoted ZZ69chevelle in post Re: Questions on 2.5" vs 3" Exhaust
I'm no expert, but I don't think ...
|Dec 2nd, 18|
|12:18 AM - engineguy quoted cdnpont in post Re: Piston ring sizing question. Stock 327 bore.
I'm going to use the origina...
|Nov 21st, 18|
|5:34 AM - impala quoted engineguy in post Re: Found extra oil port???????
I think the hole would be for ...
|Sep 18th, 18|
|10:22 PM - engineguy quoted 402chevelle71 in post Re: «Centering Pin» identification
Thank you all for the reply, I am ...
|Sep 6th, 18|
|2:51 PM - novadude quoted engineguy in post Re: Muncie carnage
When a Muncie transmission fai...
|Jul 31st, 18|
|3:24 PM - GuysMonteSS quoted engineguy in post Re: Water pump woes ...
Once the coolant warms up and ...
|1:34 PM - engineguy quoted GuysMonteSS in post Re: Water pump woes ...
Thing is,where the crack is look...
|Jul 30th, 18|
|8:21 PM - potent rodent quoted engineguy in post Re: SBC Timing cover lower pan seal Is it needed?
If you are planning to change ...
|7:30 AM - GuysMonteSS quoted engineguy in post Re: Water pump woes ...
Not a good idea to use silicon...
|Jul 29th, 18|
|10:23 PM - RichardB quoted engineguy in post Re: Carb sucking air at baseplate
Richard, There are many varia...
|Mar 17th, 18|
|12:49 AM - dyno jonn quoted engineguy in post Re: Steel or aluminum flywheel ?
STEEL for any application that...
|Mar 2nd, 18|
|4:06 PM - Cam quoted engineguy in post Re: 1974 rv 454?
...ns. So I agree with engineguy. Forged cranks were ...