Magnaflow 15893 kit not fitting - Chevelle Tech
Chevelle Tech join team chevelle as a supporting member  
Chevelle Parts at SS396.com      
GROUND UP & SS396.com         
Official Sponsor of Team Chevelle
     

Auto Insurance

Chevelles.com is the premier Chevrolet Chevelle Forum on the internet. Registered Users do not see the above ads.
Magnaflow Magnaflow

 
 
Thread Tools Search this Thread Display Modes
  #1  
Old Jan 29th, 11, 5:30 PM
StevenS StevenS is offline
Lifetime Premium Member
Steve
 
Join Date: Nov 2007
Location: Franklinville N.J.
Posts: 689
Default Magnaflow 15893 kit not fitting

Anybody have any issues with the magnaflow 2 1/2 kit for 64-67? I got the header back with x pipe all installed. Everything is centered level and straight. Mufflers sit lever and tucked up nice. But tail pipes wont go. The passenger side fits perfect. The drivers side hangs down 3 inches. looking from the rear axle both mufflers look perfect.

The exhaust that came off which I installed in 1976 had offset to offset mufflers. The magnaflow has offset to center. If both were offset I would have plenty of room to adjust. I can see that the left tailpipe is bent a little different then the right as far as bends go.
__________________
64 Chevelle 496 underway
64 F100 Street Rod with BBC /Chevy trapped in a ford body
Quick reply to this message
Sponsored Links
Advertisement
 
  #2  
Old Jan 30th, 11, 4:27 PM
StevenS StevenS is offline
Lifetime Premium Member
Steve
 
Join Date: Nov 2007
Location: Franklinville N.J.
Posts: 689
Default Re: Magnaflow 15893 kit not fitting

Well I guess I will see how good magnaflow customer service is. I cannot see anyway to fit the left side pipe other then cut and re-weld. I tryed every adjustment possible. Even if I measure it up to trim both pipes it wont work. Has to be the over the rear pipe. You can see left to right pipe are bent differently and the left is longer.

I bought this kit because it was supposed to fit not the case.
__________________
64 Chevelle 496 underway
64 F100 Street Rod with BBC /Chevy trapped in a ford body
Quick reply to this message
  #3  
Old Jan 31st, 11, 11:59 AM
Sales@JDP Sales@JDP is offline
Tech Team
Jordan
 
Join Date: Dec 2009
Location: SLC, UT
Posts: 68
Default Re: Magnaflow 15893 kit not fitting

Hi Steve,

It sounds like you need to spin and rotate the side you are having problems with.

Please feel free to call, email or PM me.

Regards,
Don
JDP Motorsports
888-308-6007
Quick reply to this message
  #4  
Old Jan 31st, 11, 6:38 PM
StevenS StevenS is offline
Lifetime Premium Member
Steve
 
Join Date: Nov 2007
Location: Franklinville N.J.
Posts: 689
Default Re: Magnaflow 15893 kit not fitting

I did try to spin and rotate that side. Tryed every adjustment possible. You can only spin the pipe so far since its so close to the upper control arms. If they use offset offset mufflers things would fit so much better. Like I said you can see the over the rear pipes are different side to side. Thank you for the help tho.
__________________
64 Chevelle 496 underway
64 F100 Street Rod with BBC /Chevy trapped in a ford body
Quick reply to this message
  #5  
Old Jan 31st, 11, 7:18 PM
Sales@JDP Sales@JDP is offline
Tech Team
Jordan
 
Join Date: Dec 2009
Location: SLC, UT
Posts: 68
Default Re: Magnaflow 15893 kit not fitting

Hello,

Give Jim Cates a call at Magnaflow he is the Head Tech person 800-990-0905. He has always been able to solve any problems I have had with Magnaflow products.

Regards,
Don
JDP Motorsports
888-308-6007
Quick reply to this message
  #6  
Old Jan 31st, 11, 7:34 PM
StevenS StevenS is offline
Lifetime Premium Member
Steve
 
Join Date: Nov 2007
Location: Franklinville N.J.
Posts: 689
Default Re: Magnaflow 15893 kit not fitting

Thanks Don. I already have a contact into magnaflow. I sent them photos and they have reviewed them. But no solution as of yet.
__________________
64 Chevelle 496 underway
64 F100 Street Rod with BBC /Chevy trapped in a ford body
Quick reply to this message
  #7  
Old Feb 26th, 12, 9:02 PM
dream66 dream66 is offline
Lifetime Premium Member
Cory
 
Join Date: Mar 2011
Location: Wimberley, TX (SW of Austin)
Posts: 1,851
Default Re: Magnaflow 15893 kit not fitting

Steve,

Any solution yet?
__________________
'66 SS 396 #'s match/ POP - Aztec Bronze / Bronze Interior
'66 SS 454 Cortez Silver / Maroon Interior (In progress)
'37 Chevy Coupe 235 Straight 6 - Cabana Cream`
'55 Chevy Gasser - 427, 4 speed
Quick reply to this message
  #8  
Old Aug 14th, 12, 7:04 AM
Davidmalibu Davidmalibu is offline
Tech Team
 
Join Date: Jun 2004
Location: FRANCE
Posts: 157
Default Re: Magnaflow 15893 kit not fitting

Steve,

Any solution yet?
I've got the same problem on my 64 coupe with that kit
Thanx

David
Quick reply to this message
  #9  
Old Aug 14th, 12, 6:30 PM
StevenS StevenS is offline
Lifetime Premium Member
Steve
 
Join Date: Nov 2007
Location: Franklinville N.J.
Posts: 689
Default Re: Magnaflow 15893 kit not fitting

Hi David. They sent me another tailpipe and I installed tubular upper controls for more clearance. Fits better but not tucked up like I would like it to.

I am not liking the Magnaflow sound. So I am going to put flowmasters on. But I will buy offset offset mufflers. The offset mufflers will without a doubt tuck the tailpipes up were they should be.
__________________
64 Chevelle 496 underway
64 F100 Street Rod with BBC /Chevy trapped in a ford body
Quick reply to this message
  #10  
Old Aug 15th, 12, 4:39 PM
BigBlockBeaumont BigBlockBeaumont is offline
Team Member
Andre
 
Join Date: Mar 2003
Location: Waterloo,ON
Posts: 427
Default Re: Magnaflow 15893 kit not fitting

I had problems with the kit for 68-72, as the left u shaped pipe that goes over the axle did not match the right. The difference could only be seen when laying the 2 pipes on the garage floor in different positions. The result was a pass side pipe that was titlited upwards towards the bumper. Struggled for days until I realized it was the pipe and when I called them they told me to return it, and they would warranty the system but since the front was all finsihed and cut to size, I just had the muffler shop splice the rear section and weld it on at the correct angle - took an extra 45 mins of labor but I was there to have the joints welded up anyway. Magnaflow claimed it was virtually impossible for this to happen since the pieces are all robotically bent and cut but......

Having said that I got the kit for a great price and I do like the sound.
__________________
1969 SS396, Lemans blue, M21, 4.10 12 bolt, Matching #'s
Quick reply to this message
Sponsored Links
Advertisement
 
 
Chevelle Tech > Supporting Vendors > Magnaflow      Current Topic: Magnaflow 15893 kit not fitting
Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Chevelle Tech forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address. Note, you will be sent a confirmation request to this address.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:42 PM.


Is there a site like this for?    El Caminos Camaros Novas Impalas GTO Chevy Punch All Chevys

2009 Team Chevelle - AutoForums