Guess what I did today......


http://img99.imageshack.us/img99/1511/backtogether009pl7.jpg (http://imageshack.us)

http://img179.imageshack.us/img179/5208/backtogether012ni0.jpg (http://imageshack.us)

http://img99.imageshack.us/img99/3727/backtogether013uo2.jpg (http://imageshack.us)

I should be able to take it for a ride tomorrow afternoon. The rear tires need and a 1/4 of rubber removed

Looks pretty frigging cool bud...it is cool to crawl around in there doing all that stuff huh??? hahahhaha I think you guys are crazy putting that dynamat everywhere but that is just me and I am sorta in the minority about that...Very good Rich...you're getting real close...Did you get the carpet under sill plates trimmed correctly??? Crap I think you basically done now right??? Sweet...

Just about ready Jeff. Carpet cut under the sills very accurate..Thanks to alot of good info from you Dude !!!!!! :thumbsup:

I want to know what you think of the Dynamat. I did the asphalt type stuff, thinking but going to the Dynamat, if people think it's worth it.

Looks awesome!!! I am getting ready to do the carpet in my 69. Where did you get the carpet from it looks great.

I want to know what you think of the Dynamat. I did the asphalt type stuff, thinking but going to the Dynamat, if people think it's worth it.


Mine is not Dynamat, too expensive. I went with this:

RAAMmat BXT60
RAAMaudio
St Helens, OR
Web site Mass Layer Butyl
Form Roll
Surface glossy aluminum
Published Lbs ft2 0.35
Measured Lbs ft2 (with release paper) 0.40
Net Measured Lbs ft2 (w/o release paper) 0.38
Published Thickness (mils) 60
Published Foil Thickness (mils)
I paid $99 for a roll that does 62 cu ft., I have quite a bit left over

BUT, if I were you I would stick to what you have. Butyl is suppose to be the better Sound Deadner, but if you already have asphalt down I wouldn't bother changing , IMO. Check this out if you have not yet.

http://www.sounddeadenershowdown.com/

Looks awesome!!! I am getting ready to do the carpet in my 69. Where did you get the carpet from it looks great.

Bought carpet from OPGI. The one thing that bothered me about this carpet is that the front piece barely over laps the back piece at the middle. If I wasn't careful it would not overlap. No trimming on upper Pass side because it barely made it there to tuck under factory insulation. On upper driver side I had to trim a few inches but over lap at middle was very close.
I was expecting maybe 3 or 4 inches overlap but ended with not quite an inch at sides (when I say sides, only at the over lap seam.) and down to near 0 as the seam goes to the console on each side (buckets will cover that anyway)..And door seal plates and front console bracket will keep it from moving. BUT, it all ended good as you see

Mine is not Dynamat, too expensive. I went with this:

RAAMmat BXT60
RAAMaudio
St Helens, OR
Web site Mass Layer Butyl
Form Roll
Surface glossy aluminum
Published Lbs ft2 0.35
Measured Lbs ft2 (with release paper) 0.40
Net Measured Lbs ft2 (w/o release paper) 0.38
Published Thickness (mils) 60
Published Foil Thickness (mils)
I paid $99 for a roll that does 62 cu ft., I have quite a bit left over

BUT, if I were you I would stick to what you have. Butyl is suppose to be the better Sound Deadner, but if you already have asphalt down I wouldn't bother changing , IMO. Check this out if you have not yet.

http://www.sounddeadenershowdown.com/

That website is a must read. Thanks, Rich.

Jim

These went in today


http://img411.imageshack.us/img411/584/backtogether016la6.jpg (http://imageshack.us)

http://img451.imageshack.us/img451/6977/backtogether017vg9.jpg (http://imageshack.us)

Man you don't need music you have a 468....hahahahah ;)

Man you don't need music you have a 468....hahahahah ;)

Your right Jeff, there just for looks.:D