I here alot of good comments about the Jegs kit. What about the Summit kit??? I here they are made by the same company (IMMCO). Also who like TA and who like torque-tech. Already heard about Pypes.

From what I've heard,Summit and Jegs are the same
Also,Torque Tech and TA are the same.
I bought a pair of 3" head pipes from Pypes and they looked identical to the TT and TA pipes I've seen

.

Have you considered the 3" stainless kit from Magnaflow w/ the x-pipe?

If you don't need an X or H setup, then I would go w/the Jegs kit. Did a buds Buick in the 3" version and it fits better than my $$$ Pypes system.

But I do have an X pipe though.

No X or H needed. Keep the votes and comment coming. :)

If you want a real good fitting sytem,buy the Flowmaster 2.5" tailpipes for $100 and Pypes sells the 3" headpipes for $60

Torque Tech all the way! :thumbsup:

Excellent fit and quality! :thumbsup:

If you want a real good fitting sytem,buy the Flowmaster 2.5" tailpipes for $100 and Pypes sells the 3" headpipes for $60

This is the way to go...would of saved me enormous headaches and alot of $$$.

Chris, did you have to modify the 3" headpipes to get to your muff (in other words, did you have to put any offsets in the head pipes)?

If you want a real good fitting sytem,buy the Flowmaster 2.5" tailpipes for $100 and Pypes sells the 3" headpipes for $60
Ok... I'll bite. Is this a special order Pypes item or something in their catalog? The closest thing I see is the DGU12 3" downpipe extensions which are 44" long.

Vince,the headpipes need no offsets.
Steve,the 3DGU12 3" downpipe extensions are what I used.
I just needed to buy 3" to 3" collectors from Summit for $20 to hook it all up.

You guys with the X pipe where does it go across your car? Under the trans or drive shaft?

http://www.chevelles.com/showroom/data/500/EXHAUST-91.JPG

I have Torque Tech 3" tailpipes and a Summit X-pipe kit

Thanks for the pic.

I have my Gear Vendors haning off the back so I may not be able to run an X pipe. If I do it will go under the GV or just behind it.

How low do they hang?

My 3" kit fit like a glove! I did ZERO pipe bending to the system. Only cutting the head pipes to fit. I advise having the system installed on a lift!

Torque kits are exspensive but TOP NOTCH!

I have learned the hard way, you get what you pay for!

This was the 4th exhaust system I have installed on my Chevelle in the past 22 years, absolutly the best!

i bought the 3" summit x pipe kit but couldn't use the x-pipe.(car sits to low) i also used the flowmaster universial 3" tailpipes and there super 40 mufflers. everything fits awsome and for the most part (two bends) is manderal.

I bought the 3" kit from summit MPE-15898 and I wasn't very happy. The exhaust came out by the back tire instead of out the rear. Bought the kit from Pypes with ceramic coating a fits like a glove on my 71 Chevelle. Part of the problem with the summit kit magnaflow brand? was the X pipe. I didn't fit under my crossmember. I need to run straight pipes cause of my crossmember has been changed to fit the t56 tranny.

Vince,the headpipes need no offsets.
Steve,the 3DGU12 3" downpipe extensions are what I used.
I just needed to buy 3" to 3" collectors from Summit for $20 to hook it all up.

Chris, which 3-to-3 inch collectors did you get from Summit? The only ones I see are from Hedman with an S-bend in them. I'd think you'd need straight ones.

Rich,I don't remember the part # specifically.But they are listed on the website if you look.
They are not the Heddman S bend type..they are straight..Summit brand btw